manualshive.com logo in svg

Agilent Technologies 5977B Series, Руководство по устранению неисправностей и техническому обслуживанию

Поделиться
Скачать
Agilent Technologies 5977B Series Скачать руководство пользователя страница 67

CI Troubleshooting

3

67

There should not be any peak visible at 

m/z

 32 (O

2

). This almost always 

indicates an air leak.

Special NCI notes

Since NCI is so extremely sensitive, air leaks that are not detectable in EI or 
PCI can cause sensitivity problems in NCI. To check for this kind of air leak in 
NCI, inject OFN. The base peak should be at 

m/z

 272. If the abundance of 

m/z

 238 is much greater than that of 

m/z

 272, you have an air leak.

How do I find the air leak?

1

See 

Figure 4

 on page 69 and 

Table 7

 on page 69.

2

Look for the last seal that was disturbed.

•

If you just pumped down the MSD, press on the sideplate to check for 
proper seal. Poor alignment between the analyzer and the GC/MSD 
interface seal can prevent the sideplate from sealing.

•

If you just replaced the reagent gas bottle or gas purifier, check the 
fittings you just opened and refastened.

Figure 3  

Looking for air leaks

Содержание 5977B Series



































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды