Agilent Technologies 5977B Series Скачать руководство пользователя страница 101

Страница: 101 / 258

General Maintenance

5977B Series MSD Troubleshooting and Maintenance Manual

101

To Reconnect the MSD to the 7890 GC

Materials needed

•

Wrench, open-end, 1/4-inch × 5/16-inch (8710-0510)

Procedure

Position the MSD so the end of the GC/MSD interface is near the GC.

Reconnect the GC/MSD interface and the LVDS cables (if applicable).

Slide the MSD to its regular position next to the GC.

Be careful not to damage the GC/MSD interface as it passes into the GC.
Ensure the end of the GC/MSD interface extends into the GC oven.

The foreline pump may be located on the floor, on the lab bench next to or
behind the MSD, or under the analyzer chamber at the back of the MSD.

Reinstall the capillary column.

Pump down the MSD.

Turn on the MS and GC. Enter appropriate temperature setpoints for the
GC/MSD interface and GC oven.





Содержание 5977B Series



































































































































































































































































Результаты поиска

Содержание 5977B Series

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies 5977B Series, Руководство по устранению неисправностей и техническому обслуживанию

Результаты поиска

Содержание 5977B Series

Отзывы:

Бренды по названию

Популярные бренды