Agilent Technologies 5977B Series Скачать руководство пользователя страница 133

Страница: 133 / 258

General Maintenance

5977B Series MSD Troubleshooting and Maintenance Manual

133

To Replace the Fan for the High Vacuum Pump

Materials needed

Fan (G7005-60564)

Screwdriver, Torx T-20 (8710-1615)

Procedure

Vent the MSD.

Remove the left side MSD cover.

Disconnect the fan wiring from the connector on the MSD frame. (See

Figure 19

on page 134.)

Remove the four fan screws and the safety grill. Remove the fan. Keep the
screws.

Install the new fan with the flow arrow on the side pointing toward the
pump. The wires should be at the upper left, close to the connector.

Add the safety grill and the four screws. Tighten the screws firmly.

Connect the fan wiring to the fan connector on the MSD frame.

Reinstall the MSD covers.

Pump down the MSD.





WA R N I N G

Do not touch the high vacuum pump. The pump could still be hot enough to burn you.

WA R N I N G

Ensure the safety grill that shields the fan blades is in place.

Содержание 5977B Series



































































































































































































































































Результаты поиска

Содержание 5977B Series

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies 5977B Series, Руководство по устранению неисправностей и техническому обслуживанию

Результаты поиска

Содержание 5977B Series

Отзывы:

Бренды по названию

Популярные бренды