Agilent Technologies 5977B Series Скачать руководство пользователя страница 137 | Manualshive

Страница: 137 / 258

Agilent Technologies 5977B Series Скачать руководство пользователя страница 137

General Maintenance

4

5977B Series MSD Troubleshooting and Maintenance Manual

137

To Lubricate the Side Plate O-Ring

Materials needed

•

Cloths, clean (05980-60051)

•

Gloves, clean, lint-free

•

Large (8650-0030)

•

Small (8650-0029)

•

Grease, Apiezon L, high vacuum (6040-0289)

The side plate O-ring needs a thin coat of grease to ensure a good vacuum seal.
If the side plate O-ring appears dry or does not seal correctly, lubricate it using
this procedure. A good test is to wipe off the side plate with methanol, then
close the analyzer chamber. If the O-ring has enough grease on it, it will leave a
faint trace on the side plate.

Procedure

1

Vent the MSD.

2

Open the analyzer chamber.

3

Use a clean, lint-free cloth or glove to spread a

thin

coat of high vacuum

grease only on the exposed surface of the O-ring. (See

4

Use a clean, lint-free cloth or glove to wipe away excess grease. If the
O-ring looks shiny, there is too much grease on it.

5

Close the analyzer chamber.

6

Pump down the MSD.

C A U T I O N

Vacuum seals other than the side plate O-ring and vent valve O-ring do not need to be
lubricated. Lubricating other seals can interfere with their correct function.

C A U T I O N

Do not use anything except the recommended vacuum grease. Excess grease can trap
air and dirt. Grease on the surface of the O-ring other than the exposed surface can trap
air, resulting in air spikes during operation.

«
...
135
136
137
138
139
...
»

Содержание 5977B Series



































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды