manualshive.com logo in svg

Agilent Technologies 5977B Series, Руководство по устранению неисправностей и техническому обслуживанию

Поделиться
Скачать
Agilent Technologies 5977B Series Скачать руководство пользователя страница 166

166

5977B Series MSD Troubleshooting and Maintenance Manual

6

Vacuum System

Vacuum Seals

Vacuum seals are shown in 

Figure 32

 on page 167.

Several types of Viton elastomer O-ring seals are used to prevent air leaks into 
the analyzer chamber. All these O-rings, and the surfaces to which they seal, 
must be kept clean and protected from nicks and scratches. A single hair, 
piece of lint, or scratch can produce a serious vacuum leak. Two of the O-rings, 
the side plate O-ring and the vent valve O-ring, are 

lightly

 lubricated with 

Apiezon-L vacuum grease.

Face seals

A face seal is an O-ring that fits in a shallow groove. The sealing surface is 
usually a flat plate. The manifold side plate and end plate O-rings fit into 
grooves around the large openings in the analyzer chamber. The side plate 
swings into place against the side plate O-ring, and must be held in place when 
the MSD is turned on for pump down to ensure a good seal.

The front and rear end plates are screwed onto the manifold and should not 
need to be removed. The GC/MSD interface fastens to the manifold with three 
screws.

The calibration valve assembly is fastened onto the front end plate by two 
screws. The vent valve knob threads into the front end plate. Small O-rings in 
grooves in the front end plate provide vacuum seals.

The diffusion pump baffle adapter has a groove for its O-ring. The baffle 
adapter is clamped to the manifold with four claw grips.

KF (NW) seals

Most of the seals for the high vacuum pumps, foreline gauge, and foreline 
pump are KF seals. KF seals have an O-ring supported by a centering ring. The 
centering ring can be either on the inside or outside of the O-ring. The clamp 
presses two flanges against the O-ring, making a seal. KF clamps must not be 
overtightened.

Содержание 5977B Series



































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды