Agilent Technologies 5977B Series Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 258

Agilent Technologies 5977B Series Скачать руководство пользователя страница 29

Introduction

1

5977B Series MSD Troubleshooting and Maintenance Manual

29

Electromagnetic compatibility

This device complies with the requirements of CISPR 11. Operation is subject
to the following two conditions:

•

This device may not cause harmful interference.

•

This device must accept any interference received, including interference
that may cause undesired operation.

If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try one or more of the following measures:

•

Relocate the radio or antenna.

•

Move the device away from the radio or television.

•

Plug the device into a different electrical outlet, so that the device and the
radio or television are on separate electrical circuits.

•

Make sure that all peripheral devices are also certified.

•

Make sure that appropriate cables are used to connect the device to
peripheral equipment.

•

Consult your equipment dealer, Agilent Technologies, or an experienced
technician for assistance.

Changes or modifications not expressly approved by Agilent Technologies
could void the user’s authority to operate the equipment.

Sound emission declaration

Sound pressure

Sound pressure Lp <70 dB according to EN 27779:1991.

Schalldruckpegel

Schalldruckpegel Lp <70 dB am nach EN 27779:1991.

«
...
27
28
29
30
31
...
»

Содержание 5977B Series



































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды