manualshive.com logo in svg

Agilent Technologies 5977B Series, Руководство по устранению неисправностей и техническому обслуживанию

Поделиться
Скачать
Agilent Technologies 5977B Series Скачать руководство пользователя страница 206

206

5977B Series MSD Troubleshooting and Maintenance Manual

7

Analyzer

Detector 

The detector (See 

Figure 49

 on page 207) in the MSD analyzer is a high energy 

conversion dynode (HED) coupled to an electron multiplier (EM). The detector 
is located at the exit end of the quadrupole mass filter. It receives the ions that 
have passed through the mass filter. The detector generates an electronic 
signal proportional to the number of ions striking it. The detector has three 
main components: the detector ion focus, the HED, and the EM horn.

Detector ion focus

The detector ion focus directs the ion beam into the HED, which is located off 
axis. The voltage on the detector focus lens is fixed at –600 V.

High energy dynode

The HED operates at –10,000 V for EI and PCI, and +10,000 V for NCI. It is 
located off-axis from the center of the quadrupole mass filter to minimize 
signals due to photons, hot neutrals, and electrons coming from the ion 
source. When the ion beam hits the HED, electrons are emitted. These 
electrons are attracted to the more positive EM horn. Do not touch the 
insulator.

EM horn

The EM horn carries a voltage of up to –3,000 V at its opening and 0 V at the 
other end. The electrons emitted by the HED strike the EM horn and cascade 
through the horn, liberating more electrons as they go. At the far end of the 
horn, the current generated by the electrons is carried through a shielded 
cable outside the analyzer to the signal amplifier board. 

The voltage applied to the EM horn determines the gain. The voltage is 
adjustable from 0 to –3,000 VDC. Use the EM voltage found in autotune as a 
baseline for the EM voltage setting.

•

To increase signal gain, increase the EM voltage. 

•

For concentrated samples where less signal gain is needed, decrease the EM 
voltage. 

Содержание 5977B Series



































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды