Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 82

Страница: 82 / 270

Troubleshooting and Maintenance Guide

Not Ready Symptoms

The Measured Column Flow Does Not Equal the Displayed Flow

If the actual column flow does not match the calculated flow
displayed on the GC, do the following:

•

Verify that the measured flows are corrected to 25 °C and
1 atmosphere.

•

Verify that the correct column dimensions are configured
accurately, including the actual (trimmed) column length.

•

The split vent line or trap may be partly plugged, creating an
actual inlet pressure higher than the setpoint pressure.

Содержание 5975T LTM GC/MSD















































































































































































































































































Результаты поиска

Содержание 5975T LTM GC/MSD

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Результаты поиска

Содержание 5975T LTM GC/MSD

Отзывы:

Бренды по названию

Популярные бренды