manualshive.com logo in svg

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Поделиться
Скачать
Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 112

112

Troubleshooting and Maintenance Guide

10

General Maintenance

•

GC/MSD interface

•

Analyzer parts

•

Vacuum pumps

•

Inlet

•

LTM column

•

Guard column heated enclosure

The GC inlets, guard column heated enclosures, and LTM 
column also operate at very high temperatures. Use the same 
caution around these parts. 

Chemical residue

Only a small portion of your sample is ionized by the ion source. 
The majority of any sample passes through the ion source 
without being ionized. It is pumped away by the vacuum system. 
As a result, the exhaust from the foreline pump will contain 
traces of the carrier gas and your samples. Exhaust from the 
standard foreline pump also contains tiny droplets of foreline 
pump oil.

An oil trap is supplied with the standard foreline pump. This 
trap stops 

only

 pump oil droplets. It 

does not

 trap any other 

chemicals. If you are using toxic solvents or analyzing toxic 
chemicals, do not use this oil trap. For all foreline pumps, install 
a hose to take the exhaust from the foreline pump outdoors or 
into a fume hood vented to the outdoors. For the standard 
foreline pump, this requires removing the oil trap. Be sure to 
comply with your local air quality regulations.

WA R N I N G

Never touch these parts while your instrument is on. After the 
instrument is turned off, give these parts enough time to cool 
before handling them.

WA R N I N G

The foreline pump can cause burns if touched when operating. It 
has a safety shield to prevent the user from touching it.

WA R N I N G

The oil trap supplied with the standard foreline pump stops only 
foreline pump oil. It does not trap or filter out toxic chemicals. If 
you are using toxic solvents or analyzing toxic chemicals, remove 
the oil trap and install a hose to take the foreline pump exhaust 
outside or to a fume hood.

Содержание 5975T LTM GC/MSD















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды