Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 255

Страница: 255 / 270

Parts

Troubleshooting and Maintenance Guide

255

EI GC/MSD Interface

Table 30

lists the replacement parts related to the EI GC/MSD

interface.

Table 30

EI GC/MSD interface

Description

Part number

GC/MSD interface (complete)

G1099-60300

Interface column nut

05980-20066

Heater sleeve

G1099-20210

Heater/Sensor assembly

G1099-60107

Insulation

G1099-20301

Setscrew for heater/sensor assembly

0515-0236

Screws, M4x0.7 panhead, for heater sleeve

0515-0383

Welded interface assembly

G1099-60301

RTGA Welded interface assembly

G2589-60060

GC/MSD interface O-ring

0905-1405

Interface cover

G1099-00005

Transfer line cover

G3170-00405

Screws for mounting interface and cover to analyzer chamber 0515-0380

Table 31

Ferrules for GC/MSD interface

Description

Part number

Preconditioned 85% Vespel, 15% Graphite

Ferrules Long (10 pack)

0.1-0.25 mm id column
0.32 mm id column

5062-3508
5062-3506

Содержание 5975T LTM GC/MSD















































































































































































































































































Результаты поиска

Содержание 5975T LTM GC/MSD

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Результаты поиска

Содержание 5975T LTM GC/MSD

Отзывы:

Бренды по названию

Популярные бренды