manualshive.com logo in svg

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Поделиться
Скачать
Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 207

Analyzer

13

Troubleshooting and Maintenance Guide

207

Quadrupole Mass Filter

The mass filter separates ions according to their mass-to-charge 
ratio (

m/z

). At a given time, only ions of a selected 

mass-to-charge ratio can pass through the filter to the detector. 
The mass filter in the MSD is a quadrupole (

Figure 32

).

The quadrupole is a fused-silica (quartz) tube coated with a thin 
layer of gold. The four hyperbolic surfaces create the complex 
electric fields necessary for mass selection. Opposing segments 
are connected; adjacent segments are electrically isolated. One 
pair has positive voltages applied, the other negative. 

A combined direct current (DC) and radio frequency (RF) signal 
is applied to the two pairs of segments. The magnitude of the RF 
voltage determines the mass-to-charge ratio of the ions that 
pass through the mass filter and reach the detector. The ratio of 
DC-to-RF determines the resolution (widths of the mass peaks). 
There are several parameters that control the DC and RF 
voltages. All these parameters are set by Autotune, but also can 
be manually adjusted in the Edit Parameters window:

•

AMU gain (AmuGain)

•

AMU offset (AmuOffs)

•

219 width (Wid219)

•

DC polarity (DC Pol)

•

Mass (axis) gain (MassGain)

•

Mass (axis) offset (MassOffs)

Figure 32

Quadrupole mass filter

Содержание 5975T LTM GC/MSD















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды