Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 132

Страница: 132 / 270

132

Troubleshooting and Maintenance Guide

General Maintenance

To Remove the Micro-Ion Vacuum Gauge

Procedure

Vent the instrument.

Remove the MSD back cover.

Disconnect the cable on the back of the Micro-Ion vacuum
gauge.

Unscrew the large thumbnut on the gauge clamp.

Remove the long screw from the clamp.

While supporting the gauge body, remove the clamp from the
mounting flange.

Remove the gauge.

If you will not be replacing the gauge soon, install the
blanking plate provided with the gauge and secure it with
the clamp, screw, and thumbnut.

Replace the rear MSD cover. See

Figure 8





Содержание 5975T LTM GC/MSD















































































































































































































































































Результаты поиска

Содержание 5975T LTM GC/MSD

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Результаты поиска

Содержание 5975T LTM GC/MSD

Отзывы:

Бренды по названию

Популярные бренды