manualshive.com logo in svg

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Поделиться
Скачать
Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 182

182

Troubleshooting and Maintenance Guide

12

Vacuum System

Overview

The vacuum system creates the high vacuum (low pressure) 
required for the instrument to operate. Without the vacuum, the 
molecular mean free path would be very short and ions would 
collide with air molecules before they could reach the detector 
operation at high pressures also would damage analyzer 
components.

The instrument uses two vacuum pumps to obtain the vacuum 
levels needed. One of two types of foreline pumps (standard or 
dry) creates a low vacuum, then a high vacuum standard 
turbomolecular (turbo) pump engages to create the vacuum 
needed for operation. 

Most vacuum system operation is automated. Operator 
interaction is through the data system or control panel. Monitor 
the vacuum system through the data system and/or local 
control panel.

Table 11

Recommended maximum flow rates per high vacuum pump 

Model number

Description

Maximum recommended 
column flow

G4362A

Standard turbo pump, EI

2.0 mL/min

Содержание 5975T LTM GC/MSD















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды