manualshive.com logo in svg

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Поделиться
Скачать
Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 224

224

Troubleshooting and Maintenance Guide

14

Electronics

Side Panel Connectors

The side panel (

Figure 36

) contains several connectors, the 

primary fuses, and several status LEDs. Most of these 
components are part of the AC board or the LAN/MS control 
card and extend through the side panel.

High vacuum power (HIVAC POWER) connector

The high vacuum power connector carries power for the turbo 
controller from the AC board.

Primary fuses

The primary fuses limit current into the MSD in case of a short 
circuit in the foreline pump. The primary fuses are on the AC 
board.

Power cord receptacle

The AC power cord brings in all electrical power for the MSD. 
The power cord can be detached from the instrument.

Foreline pump power cord receptacle

The foreline pump power cord receptacle provides AC power for 
the foreline pump. If the power switch is off, no power is 
supplied to the foreline pump.

Remote start connector

The remote start connector is the external connector for the 
remote start circuitry on the LAN control card. It combines the 
readiness condition and start/stop events signals from the GC 
control system and the MSD control system for synchronized 
communications with other instruments.

GC-LAN and MSD-LAN (I/O) connectors

The GC and MSD LAN cables from the data system are 
connected to the I/O LAN connectors. These cables carry all 
data communication between the PC and the instrument.

Содержание 5975T LTM GC/MSD















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды