manualshive.com logo in svg

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Поделиться
Скачать
Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 220

220

Troubleshooting and Maintenance Guide

14

Electronics

•

Supplies and controls the power for the ion source and 
quadrupole (mass filter) heaters.

•

Provides 24 VDC power for the cooling fans.

Signal amplifier board

The signal amplifier board amplifies the output of the detector. 
It produces an output voltage of 0 to 10 volts DC, proportional 
to the logarithm of the input current of 3 picoamps to 
50 microamps.

An analog-to-digital converter converts the amplifier output 
voltage to digital information. The LAN/MSD control card 
converts the data into abundance counts proportional to the 
detector signal current.

MSD AC board

The MSD AC board is mounted on the opposite side of the MSD 
electronics panel from the LAN/MSD control card. The AC 
board is also sometimes called the power distribution/vacuum 
control board. It performs these functions:

•

Provides input voltage transparency for the MSD.

•

Distributes AC line power to the AC/DC power supply, the 
foreline pump, and the turbo pump controller.

•

Turns the calibration valve on or off as directed by the main 
board.

•

Provides the voltage for the calibration valve.

•

Provides a logic interface to turbo controller.

•

Passes the turbo pump speed and other vacuum status 
information to the main board.

•

Turns off the foreline pump in case of a problem with 
pumpdown.

Turbo pump control

Your instrument is equipped with a turbo pump with an 
integrated controller.

The MSD AC board sends control signals to, and receives turbo 
pump status information from, the turbo pump controller. The 
turbo pump controller provides power to the turbo pump and 
regulates pump speed. If the pump fails to reach 80% speed 
within 7 minutes after beginning pumpdown or if the speed 
drops below 50% during operation, the controller shuts off the 
turbo pump and the AC board shuts off the foreline pump.

Содержание 5975T LTM GC/MSD















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды