Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 179

Страница: 179 / 270

Maintaining the Split/Splitless Inlet

Troubleshooting and Maintenance Guide

179

To Clean the Split/Splitless Inlet

Gather the following:

•

Replacement septum (See

“Consumables and Parts for

the Split/Splitless Inlet”

on page 168.)

•

Replacement liner

•

Replacement O-ring

•

Replacement gold seal

•

Replacement washer

•

Solvent that will clean the type of deposits in your inlet

•

Compressed, filtered, dry air or nitrogen

•

Beaker

•

Cleaning brushes—The FID cleaning kit (part number
9301-0985) contains appropriate brushes

•

Lint-free gloves

Load the maintenance method and wait for the GC to
become ready.

Remove the inlet liner.

Disconnect the column from the inlet.

Remove the reducing nut and gold seal. (See

“To Replace the

Gold Seal on the Split/Splitless Inlet”

on page 174.)

Place a beaker in the oven under the inlet to catch the
solvent.

Soak a cleaning brush in the solvent and scrub the inside of
the inlet weldment. Repeat 10 times.

Rinse the inlet with the solvent.

Blow the inside of the inlet dry with compressed air or
nitrogen.

WA R N I N G

Be careful! The oven and/or inlet may be hot enough to cause
burns. If the inlet is hot, wear heat-resistant gloves to protect your
hands

C A U T I O N

Wear clean, lint-free gloves to prevent contamination of parts with
dirt and skin oils.

Содержание 5975T LTM GC/MSD















































































































































































































































































Результаты поиска

Содержание 5975T LTM GC/MSD

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Результаты поиска

Содержание 5975T LTM GC/MSD

Отзывы:

Бренды по названию

Популярные бренды