Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 172

Страница: 172 / 270

172

Troubleshooting and Maintenance Guide

Maintaining the Split/Splitless Inlet

To Clean the Septum Seat in the Insert Assembly of the Split/Splitless Inlet

Gather the following:

•

Replacement septum (See

“Consumables and Parts for

the Split/Splitless Inlet”

on page 168.)

•

Wrench, hex for changing septum

•

0- or 00-grade steel wool (optional)

•

Tweezers

•

Compressed, filtered, dry air or nitrogen

•

Wrench, capillary inlet (optional)

Load the maintenance method (see the

5975T LTM GC/MSD

Operation Manual

) and wait for the GC to become ready.

Slide the locking tab forward (counterclockwise). Lift the
septum assembly straight up and away from the inlet to
avoid chipping or breaking the liner.

Remove the septum retainer nut or Merlin cap.

WA R N I N G

Be careful! The oven and/or inlet may be hot enough to cause
burns. If either is hot, wear heat-resistant gloves to protect your
hands

Содержание 5975T LTM GC/MSD















































































































































































































































































Результаты поиска

Содержание 5975T LTM GC/MSD

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Результаты поиска

Содержание 5975T LTM GC/MSD

Отзывы:

Бренды по названию

Популярные бренды