Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 217

Страница: 217 / 270

Electronics

Troubleshooting and Maintenance Guide

217

Local Control Panel and Power Switch

Local Control Panel (LCP)

You can view system status and perform some control functions
from the local control panel on the front of the instrument.

Functions available through the local control panel include:

•

Set IP address for MSD and GC

•

Prepare to vent (cool analyzer and turn off high vacuum
pump)

•

Monitor instrument status

•

Run autotune

•

Run method

•

Run sequence

•

View and set analyzer temperatures

•

View LTM column temperature, inlet temperature and
GC/MSD interface temperature

•

View inlet flows

•

Display error messages

See also

The G1701EA

GC/MSD ChemStation Getting Started

manual.

Power switch

The power switch is part of the electronics module and is
located on the lower left of the front of the instrument. It is used
to turn the instrument and foreline pump on and off.

C A U T I O N

Do not switch the instrument off unless it has completed the vent
program. Incorrect shutdown can seriously damage the MSD.

Содержание 5975T LTM GC/MSD















































































































































































































































































Результаты поиска

Содержание 5975T LTM GC/MSD

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Результаты поиска

Содержание 5975T LTM GC/MSD

Отзывы:

Бренды по названию

Популярные бренды