manualshive.com logo in svg

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Поделиться
Скачать
Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 145

General Maintenance

10

Troubleshooting and Maintenance Guide

145

4

Abrasively clean the surfaces that contact the sample or ion 
beam.

Use an abrasive slurry of alumina powder and reagent-grade 
methanol on a cotton swab. Use enough force to remove all 
discolorations. Polishing the parts is not necessary; small 
scratches will not harm performance. Also abrasively clean 
the discolorations where electrons from the filaments enter 
the source body.

5

Rinse away all abrasive residue with reagent-grade 
methanol.

Make sure 

all

 abrasive residue is rinsed way 

before

 

ultrasonic cleaning. If the methanol becomes cloudy or 
contains visible particles, rinse again.

6

Separate the parts that were abrasively cleaned from the 
parts that were not abrasively cleaned.

7

Ultrasonically clean the parts (each group separately) for 15 
minutes in each of the following solvents:

•

Methylene chloride (reagent-grade)

•

Acetone (reagent-grade)

•

Methanol (reagent-grade)

8

Place the parts in a clean beaker. 

Loosely

 cover the beaker 

with clean aluminum foil (dull side down).

9

Dry the cleaned parts in an oven at 100  °C for 5–6 minutes.

    

            

WA R N I N G

All of these solvents are hazardous. Work in a fume hood and take 
all appropriate precautions.

WA R N I N G

Let the parts cool before you handle them.

N O T E

Take care to avoid recontaminating cleaned and dried parts. Put on new, clean 
gloves before handling the parts. Do not set the cleaned parts on a dirty 
surface. Set them only on clean, lint-free cloths.

Содержание 5975T LTM GC/MSD















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды