Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 118

Страница: 118 / 270

118

Troubleshooting and Maintenance Guide

General Maintenance

Maintaining the Vacuum System

Periodic maintenance

As listed earlier in

Table 5

, some maintenance tasks for the

vacuum system must be performed periodically. These include:

•

Checking the foreline pump fluid (every week)

•

Checking the calibration vial (every 6 months)

•

Ballasting the foreline pump

•

Replacing the foreline pump oil every 6 months

•

Tightening the foreline pump oil box screws (first oil change
after installation, standard foreline pump)

•

Checking the dry foreline pump diaphragms (typically every
3 years)

Failure to perform these tasks as scheduled can result in
decreased instrument performance. It can also result in damage
to your instrument.

Other procedures

Tasks such as replacing a Micro-Ion vacuum gauge should be
performed only when needed. See

Chapter 3

or the online help

in the GC/MSD ChemStation software for symptoms that
indicate this type of maintenance is required.

More information is available

If you need more information about the locations or functions of
vacuum system components, See

“Vacuum System”

on page 181.

Most of the procedures in this chapter are illustrated with video
clips on this 5975 Series MSD User Information DVD.

Содержание 5975T LTM GC/MSD















































































































































































































































































Результаты поиска

Содержание 5975T LTM GC/MSD

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Результаты поиска

Содержание 5975T LTM GC/MSD

Отзывы:

Бренды по названию

Популярные бренды