wsm Kubota L4100 Workshop Manual Download Page 102 | Manualshive

Page: 102 / 346

background image

ENGINE

L4100, WSM

1-S30

(EU)

Governor Springs and Speed Control Plate

NOTE

• Specific tool (1):

1.2 mm (0.047 in.) diameter hard wire with its end hooked,
overall length 200 mm (7.87 in.).
The tip of wire is bent like the hook to hang governor
springs.

1. Remove the injection pump cover.
2. Remove the speed control plate (6) mounting nuts and bolts.
3. Using the specific tool (1), undo the large governor spring (2)

from the fork lever (3).

4. Using the specific tool (1), undo the small governor spring (4)

from the fork lever (3).

5. Set the speed control lever (5) as shown in the figure.
6. Take out the speed control plate (6) with care not to let the large

(2) and small (4) governor springs come off this plate and fall
into the gear case.

(To be continued)

(1) Specific Tool
(2) Large Governor Spring
(3) Fork Lever

(4) Small Governor Spring
(5) Speed Control Lever
(6) Speed Control Plate

KiSC issued 08, 2012 A

«
...
100
101
102
103
104
...
»

Summary of Contents for Kubota L4100



























































































































































































































































































































































Reviews:

No comments

Related manuals for Kubota L4100

Brand: Kellfri Pages: 32

Brand: Allis-Chalmers Pages: 220

Brand: Allis-Chalmers Pages: 312

Brand: Curtis Pages: 8

JOHN DEERE 4120

Brand: Curtis Pages: 11

TRANSCAR Series

Brand: GOLDONI Pages: 154

Brand: R2 RINALDI Pages: 32

Brand: MTD Pages: 8

Brand: McCulloch Pages: 108

Marathon RAMJET Signature J-250SC

Brand: Dover Pages: 47

Groom Master II

Brand: Jacobsen Pages: 24

Brand: Homelite Pages: 24

Brand: SAME Pages: 288

Brand: Electrolux Pages: 2

Single Row Walking Tractor

Brand: Knapik Pages: 34

Brand: GRADEN Pages: 26

Brand: GRADEN Pages: 24

Brand: AGCO Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands