background image

     INST

ALLA

TION & OWNER’S MANUAL 

The contents of this envelope are the property of the owner.  
Be sure to leave with the owner when installation is complete. 

  

CAB INSTALLATION INSTRUCTIONS

 

                                         

JOHN DEERE 2305, 2210 

           HARD SIDED CAB ENCLOSURE (p/n 1JD2305AS) 
           SOFT SIDED CAB ENCLOSURE  (p/n 1JD2305SS)

 

  

This Curtis Cab is designed and  

manufactured for use only as reasonable 
weather protection. This cab is not appli-

cable, Nor should the cab be considered as protection against  
roll over, collision or other accidents that may result. This cab is 

NOT

 

a

 

R.O.P.S.

 

cab. 

Extreme

 care should be taken when operat-

ing and by qualified, experienced operators only

.

 

 

 

Exposure

 

to

 

Carbon

 

Monoxide

 

can

 

Cause

 

illness,

 

serious

 

injury

 

or

 

death.

 

Never 

operate vehicle if suspicious of Carbon 

Monoxide. Inspect exhaust system for leaks monthly. Leaks can 
result from loose connections, corrosion, cracks or other damage 
to the exhaust manifold. If leaks are found, repair or replace 
exhaust system. Do not use vehicle until repair or replacement is 
complete. 

p. 1 of 8,  Rev. J,  
1/3/2012 

  CABS/BLADES/ SPREADERS/ACCESSORIES 

  driver and passenger.

  Curtis accessory weights are listed in product

  add additional weight to the base vehicle. All

  Curtis Cabs, blades and general accessories

ADDED

WEIGHT

  brochures. Deduct the accessory's total weight
  from the vehicle's rated capacity and never
  exceed the vehicle's rated capacity including

Note: soft side cab shown 

p/n: IM-1JD2305 

Summary of Contents for 1JD2305AS









Reviews: