wsm Kubota L4100 Workshop Manual Download Page 133 | Manualshive

Page: 133 / 346

background image

CLUTCH

L4100, WSM

2-M2

(EU)

Shift Linkage

The PTO Clutch control lever (1) and the PTO clutch

valve (4) are connected by the shift cable (3) as shown
in the left figure.

When the shift lever is moved to the

"B"

side, the

PTO clutch valve (4) is set at

"ENGAGED"

position.

Then the oil flows to clutch pack through the PTO clutch
valve (4), and the clutch pack is engaged and the PTO
shaft rotates. When the shift lever is moved to the

"A"

side, the PTO clutch valve (4) is set at the

"DISENGAGED"

position.

9Y1210278CLM0006US0

Oil Flow

The oil adjusted the pressure by the regulator valve

flows into the PTO clutch valve (2). When the PTO lever
is at the

"DISENGAGED"

position, the oil does not flow

through the PTO clutch valve (2) to the PTO clutch pack
(3).

When the PTO lever is at the

"ENGAGED"

position,

the oil flows through the PTO clutch valve (2) to the
accumulator (4) and the PTO clutch pack (3) to engage
it.

9Y1210278CLM0004US0

(1) PTO Clutch Control Lever
(2) Lever Guide

(3) Shift Cable
(4) PTO Clutch Valve

(1) Check Valve
(2) PTO Clutch Valve
(3) PTO Clutch Pack
(4) Accumulator

A: From Regulator Valve
B: Pressure Check Port

KiSC issued 08, 2012 A

«
...
131
132
133
134
135
...
»

Summary of Contents for Kubota L4100



























































































































































































































































































































































Reviews:

No comments

Related manuals for Kubota L4100

MAGNATRAC MH8000

Brand: Struck Pages: 69

Brand: Case Pages: 434

Brand: PRONAR Pages: 88

Brand: Walker Pages: 28

Proxima GP Series

Brand: Zetor Pages: 226

Brand: SaMASZ Pages: 29

Brand: Cub Cadet Pages: 48

Brand: Toro Pages: 4

Brand: Hurricane Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands