VESPA 946 E4 EMEA 2021 Manual Download

Page: 263 / 283

Headlight assy.

- Remove the leg shield back plate.

- Remove the footrest.

- Disconnect the connectors of the light assembly

and the instrument panel and free the cables from

the retaining clamps.

- Remove the headlight frame by unscrewing the

2 indicated screws.

- Remove the headlight cover by unscrewing the

indicated screws on both sides of the headlight.

- Remove the front handlebar cover.

- Undo the 2 screws indicated.

- Remove the screw indicated on both sides of the

headlight.

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

Chassis

CHAS - 263

Summary of Contents for 946 E4 EMEA 2021




























































































































































































































































































Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands

VESPA 946 E4 EMEA 2021, Manual

Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands