VESPA 946 E4 EMEA 2021 Manual Download Page 244

Page: 244 / 283

3.5 MM

Max. deviation allowed:

0.1 mm

Front brake disc

Removal

- Remove the front wheel hub.

- Undo the screws indicated.

Refitting

- Carry out the removal steps but in the reverse order, paying attention to the prescribed torques.

- Check the gap between tone wheel and front speed sensor.

Locking torques (N*m)

brake disc screws

8 - 10

Disc Inspection

- Remove the rear wheel.

- Use a calliper to check the disc thickness as

shown in the photograph.

- Repeat the measurement at no fewer than six

points on the disc.

Braking system

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

BRAK SYS - 244

Summary of Contents for 946 E4 EMEA 2021




























































































































































































































































































Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands

VESPA 946 E4 EMEA 2021, Manual

Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands