VESPA 946 E4 EMEA 2021 Manual Download

Page: 148 / 283

Wheel axle bearing removal

- Remove the bearing using the specific tools

Specific tooling

001467Y009

Bell for OD 42-mm bearings

001467Y013

Calliper to extract ø 15-mm bear-

ings

Removing the wheel axle bearings

- Support the hub cover properly to avoid damag-

ing the sealing surface with the crankcase.

- Remove the Seeger ring from the outside.

- Operating on the inside, remove the oil seal.

- Remove the wheel axle bearing using the specific

tool.

Specific tooling

020376Y

Adaptor handle

020364Y

25-mm guide

020359S

42 x 47 mm Adaptor

Removing the intermediate gear bearing

- Remove the bearing using the specific tools

Specific tooling

001467Y013

Calliper to extract ø 15-mm bear-

ings

001467Y009

Bell for OD 42-mm bearings

Engine

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

ENG - 148

Summary of Contents for 946 E4 EMEA 2021




























































































































































































































































































Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands

VESPA 946 E4 EMEA 2021, Manual

Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands