VESPA 946 E4 EMEA 2021 Manual Download Page 91

Page: 91 / 283

2. Engine main cable harness

3. H.V. coil cable harness

4. ABS control unit cable harness

5. Rear wheel speed sensor cable harness

6. Engine temperature sensor and injector ca-

ble harness

7. CDI control unit cable harness

8. Flywheel and lambda probe cable harness

Checks and inspections

Immobiliser

The electronic ignition system is controlled by the

control unit with the integrated Immobilizer sys-

tem. The Immobilizer is an antitheft system which

allows the vehicle to function only if it is activated

by means of the coded keys that the control unit

recognises. The code is integrated in a transpond-

er in the key block. This allows the driver clear

operation without having to do anything other than

just turning the key. The Immobilizer system con-

sists of the following components:

- Control unit

- Immobilizer antenna

- master and service keys with built-in transponder

- H.V. coil

- diagnosis LED

The diagnosis LED also works as a theft-deterrent

blinker. This function is activated every time the

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

Electrical system

ELE SYS - 91

Summary of Contents for 946 E4 EMEA 2021




























































































































































































































































































Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands

VESPA 946 E4 EMEA 2021, Manual

Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands