VESPA 946 E4 EMEA 2021 Manual Download

Page: 138 / 283

Inspecting the clutch drum

- Make sure that the clutch housing is not worn or

damaged.

- Measure the clutch housing inside diameter.

Characteristic

Clutch housing max. value

Max. value: Ø 134.5 mm

clutch housing standard value

Standard value: Ø 134 - 134.2 mm

Checking the bell working surface eccentricity

- Install the bell on a driven pulley shaft using 2

bearings (inside diameter: 15 and 17 mm).

- Lock with the original spacer and nut.

- Place the bell/shaft unit on the support to check

the crankshaft alignment.

- Using a dial gauge and the magnetic base, meas-

ure the bell eccentricity.

- Repeat the measurement at 3 positions (Central,

internal, external).

- In case of faults, replace the bell.

Specific tooling

020074Y

Support base for checking crankshaft

alignment

020335Y

Magnetic mounting for dial gauge

Characteristic

clutch housing check: Limit eccentricity.

Admissible limit eccentricity: 0.15 mm

Engine

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

ENG - 138

Summary of Contents for 946 E4 EMEA 2021




























































































































































































































































































Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands

VESPA 946 E4 EMEA 2021, Manual

Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands