VESPA 946 E4 EMEA 2021 Manual Download Page 58

Page: 58 / 283

Engine oil filter

Change oil and replace filter as indicated in the

scheduled maintenance table. Use new oil of the

recommended type for topping up and changing

purposes.

Make sure the pre-filter and drainage plug O-rings

are in good conditions. Lubricate them and refit the

mesh filter and the oil drainage plug, screwing

them up to the prescribed torque. Refit the new

cartridge filter being careful to lubricate the O-ring

before fitting it. Change the engine oil.

Recommended products

Engine oil 5W -40

Synthetic-based lubricant for

four-stroke engines.

SAE 5W-40; JASO MA, MA2; API SL; ACEA A3

Characteristic

Engine oil

1,340 cm³ (of which 120 cm³ in the filtering car-

tridge)

Oil pressure warning light

The vehicle is equipped with a telltale light on the

dashboard that lights up when the key is turned to

the «ON» position. This warning light will turn off

when the engine comes on.

If the light turns on during braking, at idling

speed or while turning a corner, it is necessary

to check the oil level and the lubrication sys-

tem.

Maintenance

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

MAIN - 58

Summary of Contents for 946 E4 EMEA 2021




























































































































































































































































































Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands

VESPA 946 E4 EMEA 2021, Manual

Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands