VESPA 946 E4 EMEA 2021 Manual Download

Page: 212 / 283

- With the extractor and the bell remove the bear-

ing on the outside.

Specific tooling

001467Y009

Bell for OD 42-mm bearings

001467Y013

Calliper to extract ø 15-mm bear-

ings

- Remove the oil seal of the bearing on brake disc

side.

- Remove the bearing using the guide, the adaptor

and the handle.

Specific tooling

020363Y

20-mm guide

020456Y

Ø 24 mm adaptor

020376Y

Adaptor handle

- With a specific gun heat the seat of the bearing

on the brake disc side.

Specific tooling

020151Y

Air heater

Suspensions

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

SUSP - 212

Summary of Contents for 946 E4 EMEA 2021




























































































































































































































































































Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands

VESPA 946 E4 EMEA 2021, Manual

Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands