VESPA 946 E4 EMEA 2021 Manual Download Page 52 | Manualshive

Page: 52 / 283

background image

km x 1,000 or (months) maximum

1 (1)

5 (5)

10 (10)

15 (15)

20 (20)

25 (25)

30 (30)

Engine oil filter

R

R

R

R

Valve clearance

A

A

A

A

Clutch assembly

I

Electrical system and battery

I

I

I

I

I

I

I

Braking system

I

I

I

I

Cylinder cooling system

I

Brake fluid **

I

I

I

I

I

I

I

Engine oil*

R

I

R

I

R

I

R

Hub oil

I

I

I

Headlight direction adjustment

I

I

I

Brake pads

I

I

I

I

I

I

Sliding shoes / CVT rollers

I

R

I

Engine oil pre-filter

C

C

C

C

Tire pressure and wear

I

I

I

I

I

I

I

Vehicle road test

I

I

I

I

Driven pulley - roller casings

I

L

I

Suspensions

I

I

I

Steering

A

A

A

A

Transmission

L

L

L

Labour time (minutes)

170

50

250

50

250

50

260

N.B.

AT EACH SCHEDULED MAINTENANCE MUST BE VERIFIED WITH THE DIAGNOSTIC TOOL IF
THERE ARE ERRORS AND THE IF THE PARAMETERS ARE CORRECT.
ENSURE THAT THE VEHICLE CALIBRATION IS UP TO DATE AFTER UPDATING THE DIAGNOS-
TIC TOOL.

CAUTION

AFTER THE PROVIDED MAINTENANCE PROGRAM IS INDICATED TO PROCEED WITH THE
MAINTENANCE OF THE VEHICLE STARTING FROM THE SERVICE OF 5,000 Km (3,106 mi) OR
5 MONTHS.

N.B.

THE TIMES LISTED ON THE SCHEDULED MAINTENANCE TABLE INCLUDE TIME DEDICATED
TO MANAGEMENT ACTIVITIES.

Recommended products

Piaggio Group recommends the use of prod-

ucts from its Castrol official partner for the

scheduled maintenance of its vehicles.

Only use lubricants and fluids which meet or ex-

ceed the performance characteristics specified.

This also applies when topping up only.

TABLE OF RECOMMENDED PRODUCTS

Product

Description

Specifications

Engine oil 5W -40

Synthetic-based lubricant for four-stroke

engines.

SAE 5W-40; JASO MA, MA2; API SL;

ACEA A3

Transmission oil 80W-90

Lubricant for gearboxes and transmis-

sions.

SAE 80W-90 API GL-4

DOT 4 brake fluid

Synthetic brake fluid.

SAE J 1703; FMVSS 116; ISO 4925; CU-

NA NC 956 DOT4

Lubricant grease

Lithium and medium fibre yellow brown

coloured grease suitable for various

uses.

ISO L-X-BCHA 3 - DIN 51 825 K3K -20

Water repellent spray grease

Water repellent pouring calcium spray

grease.

White, soap base spray grease with NLGI

2 Calcium complex; ISO-L-XBCIB2

Maintenance

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

MAIN - 52

«
...
50
51
52
53
54
...
»

Summary of Contents for 946 E4 EMEA 2021




























































































































































































































































































Reviews:

No comments

Related manuals for 946 E4 EMEA 2021

Brand: Super Handy Pages: 6

Uscooters Booster GT

Brand: e-TWOW Pages: 20

Brand: eZip Pages: 2

Brand: KOMFI-RIDER Pages: 28

LX 125 150 Euro 3

Brand: VESPA Pages: 74

Brand: Baotian Pages: 32

Brand: Roma Medical Pages: 20

Brand: Gilera Pages: 255

Brand: Stars n Stripes Pages: 38

Brand: Sunrise Medical Pages: 55

Y-E-S Series PUMA

Brand: Handicare Pages: 102

Brand: Ace Sports Pages: 24

Boomerbuggy X Pro

Brand: Daymak Pages: 40

Brand: Jetson Pages: 28

EcoSmart Metro HD

Brand: Razor Pages: 16

Brand: Yamaha Pages: 74

Brand: UNAGI Pages: 6

Brand: HOMCOM Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands