VESPA 946 E4 EMEA 2021 Manual Download | Manualshive

Page: 248 / 283

background image

CAUTION

THE BLEEDING OPERATIONS OF THE BRAKING SYS-
TEM, EVEN FOR THE VERSION EQUIPPED WITH ABS
SYSTEM, DO NOT ALLOW THE USE OF DIAGNOSTIC
TESTER, AND ARE THEREFORE EQUAL TO THOSE DE-
SCRIBED FOR THE STANDARD BRAKE SYSTEM.

N.B.

DURING THE BLEEDING OPERATIONS, MAKE SURE THE
BRAKE FLUID DOES NOT COME INTO CONTACT WITH
THE BODYWORK SO AS NOT TO DAMAGE IT. FURTHER-
MORE, DURING THE BLEEDING OPERATIONS REGARD-
ING THE BRAKE CALLIPERS, MAKE SURE THE BRAKE
FLUID DOES NOT COME INTO CONTACT WITH THE DISC
BRAKES AND WITH THE BRAKE PADS. FAILURE TO OB-
SERVE THIS PRECAUTION WILL ENDANGER THE PROP-
ER WORKING AND EFFICIENCY OF THE BRAKING SYS-
TEM

Specific tooling

020329Y

Mity-Vac vacuum pump

Locking torques (N*m)

Oil bleed screw

12 - 16

Front

- Remove the rubber cap from the bleed screw.

- Insert a rubber pipe in the bleed screw to permit

the brake fluid to be recovered.

- With the brake lever, load the system and bring

it up to the required pressure.

- Keeping the brake lever pulled, loosen the bleed

screw to purge the air in the system. Then tighten

the bleed screw

- Repeat the operation until only brake fluid comes

out of the rubber pipe.

- Remove the fluid recovery pipe and refit the rub-

ber cap over the bleed screw.

- Top up the brake fluid to the right level in the res-

ervoir. If necessary, bleeding can be done using a

special vacuum pump

N.B.

DURING THE BLEEDING OPERATIONS, MAKE SURE THE
BRAKE FLUID DOES NOT COME INTO CONTACT WITH
THE BODYWORK SO AS NOT TO DAMAGE IT. FURTHER-
MORE, DURING THE BLEEDING OPERATIONS REGARD-
ING THE BRAKE CALLIPERS, MAKE SURE THE BRAKE
FLUID DOES NOT COME INTO CONTACT WITH THE DISC
BRAKES AND WITH THE BRAKE PADS. FAILURE TO OB-
SERVE THIS PRECAUTION WILL ENDANGER THE PROP-
ER WORKING AND EFFICIENCY OF THE BRAKING SYS-
TEM

CAUTION

Braking system

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

BRAK SYS - 248

«
...
246
247
248
249
250
...
»

Summary of Contents for 946 E4 EMEA 2021




























































































































































































































































































Reviews:

No comments

Related manuals for 946 E4 EMEA 2021

Brand: E-Wheels Pages: 4

Brand: Myria Pages: 50

Brand: Oxybul Pages: 13

Brand: Furo Systems Pages: 14

Brand: IU Pages: 16

Brand: Airebike Pages: 21

Brand: JUPITERBIKE Pages: 37

VELOCIPTOR ES 85W

Brand: Trevi Pages: 16

Brand: BMX Pages: 5

Brand: C.T.M. Pages: 17

Brand: KUGOO Pages: 12

Brand: KUGOO Pages: 4

Brand: Lime Pages: 15

Brand: KBO Pages: 22

Brand: Radio Flyer Pages: 6

Brand: Xingyue Pages: 58

Brand: RAMBO Pages: 29

Brand: Jetson Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands