VESPA 946 E4 EMEA 2021 Manual Download | Manualshive

Page: 100 / 283

background image

CAUTION

PROCEED WITH CAUTION.
DO NOT DAMAGE THE TABS AND/OR THEIR CORRESPONDING SLOTS. HANDLE THE PLASTIC
AND PAINTED COMPONENTS WITH CARE, DO NOT SCRATCH OR IMPAIR THEM.

During refitting of the central cover, ensure the correct position of the rubber protection. Refer to para-

graph "

Battery compartment - Inverter

" in the "

Bodywork

" chapter.

Sealed battery

If the vehicle is provided with a sealed battery, the only maintenance required is the check of its charge

and recharging, if necessary.

These operations should be carried out before delivering the vehicle, and on a six-month basis while

the vehicle is stored in open circuit.

Besides upon pre-delivery it is therefore necessary to check the battery charge and recharge it, if re-

quired, before storing the vehicle and afterwards every six months.

INSTRUCTIONS FOR BATTERY REFRESH AFTER OPEN CIRCUIT STORAGE

1) Voltage check

Before installing the battery on the vehicle, check the open circuit voltage with a standard tester.

- If voltage exceeds 12.60 V, the battery can be installed without any renewal recharge.

- If voltage is below 12.60 V, a renewal recharge is required as explained in 2).

2) Constant voltage battery charge mode

- Constant voltage charge equal to 14.40 - 14.70V

- Initial charge voltage equal to 0.3 - 0.5 for Nominal capacity

- Charge time:

10 - 12 h recommended

Minimum 6 h

Maximum 24 h

3) Constant current battery charge mode

- Charge current equal to 1/10 of the battery rated capacity

- Charge time: Maximum 5 h

See also

Vano portabatterie - inverter

Battery installation

VRLA battery (valve-regulated lead-acid battery) Maintenance Free (MF)

WARNING

BATTERY ELECTROLYTE IS TOXIC AND IT MAY CAUSE SERIOUS BURNS. IT CONTAINS SUL-
PHURIC ACID. AVOID CONTACT WITH EYES, SKIN AND CLOTHING. IF IT ACCIDENTALLY
COMES INTO CONTACT WITH YOUR EYES OR SKIN, WASH WITH ABUNDANT WATER FOR
APPROX. 15 MIN. AND SEEK IMMEDIATE MEDICAL ATTENTION.

Electrical system

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

ELE SYS - 100

«
...
98
99
100
101
102
...
»

Summary of Contents for 946 E4 EMEA 2021




























































































































































































































































































Reviews:

No comments

Related manuals for 946 E4 EMEA 2021

Brand: Super Handy Pages: 6

Brand: Pride Mobility Pages: 34

ICe Q5 EVOLUTION

Brand: Ice Pages: 34

Brand: Hudora Pages: 8

Brand: Hudora Pages: 8

Brand: KOMFI-RIDER Pages: 20

Brand: Hover-1 Pages: 21

Brand: 2GOability Pages: 30

Brand: ESAL Pages: 9

Brand: Cagiva Pages: 159

Brand: Malaguti Pages: 44

Brand: Malaguti Pages: 45

Brand: Malaguti Pages: 72

Brand: Roma Medical Pages: 16

Brand: FREERIDER Pages: 32

Brand: Scootacar Pages: 19

Brand: Macwheel Pages: 20

Brand: niu Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands