VESPA 946 E4 EMEA 2021 Manual Download

Page: 145 / 283

- Check that stationary driving pulley does not

show signs of abnormal wear on the grooved edge

and on the surface in contact with the belt.

CAUTION

DO NOT LUBRICATE OR CLEAN SINTERED BUSHINGS

Characteristic

movable driving half-pulley bushing: Standard
Diameter

26.000 - 26.021 mm

Sliding bushing

Ø26 (-0.020 -0.041)mm

Characteristic

CVT rollers ø 19 mm

Wear limit ø 18.4 mm

Refitting the driving pulley

- perform the operations in reverse order of disas-

sembly.

CAUTION

INSERT THE ROLLERS WITH THE LARGEST SUPPORT
SURFACE ACCORDING TO THE DIRECTION OF ROTA-
TION.

- tighten the torque using the specific tool to lock

the pulley.

CAUTION

DURING THE INSTALLATION PAY SPECIAL ATTENTION
TO THE ASSEMBLY OF THE SPRING WASHER, AS
SHOWN IN FIGURE.

Specific tooling

020938Y

Drive pulley lock

Locking torques (N*m)

driving pulley retainer nut

75 - 83

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

Engine

ENG - 145

Summary of Contents for 946 E4 EMEA 2021




























































































































































































































































































Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands

VESPA 946 E4 EMEA 2021, Manual

Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands