VESPA 946 E4 EMEA 2021 Manual Download Page 188

Page: 188 / 283

Refitting

- Follow the steps in reverse order to the removal,

tightening the screws to the specified torque.

- Insert the oil pump.

- Insert the control sprocket and the chain.

N.B.

FIT THE BELLEVILLE WASHER SO THAT ITS OUTER RIM
TOUCHES THE PULLEY. MAKE SURE THAT THE PUMP
TURNS FREELY.

Recommended products

Loctite 243

Medium strength thread-locking

sealant.

Blue

Locking torques (N*m)

Screws fixing oil pump to the crankcase

5 to 6

- Preventing rotation, tighten the water pump com-

mand screw complete with washer.

Engine

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

ENG - 188

Summary of Contents for 946 E4 EMEA 2021




























































































































































































































































































Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands

VESPA 946 E4 EMEA 2021, Manual

Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands