VESPA 946 E4 EMEA 2021 Manual Download

Page: 95 / 283

2. Previously unused control unit - transpond-

er absent or cannot be used

: the LED is on

permanently. In this condition no operations are

possible including the start up of the vehicle.

Programmed control unit - the service key in

(normal condition of use)

: a single 0.7-second

flash is displayed, after which the LED remains off

steadily. The engine can be started.

Programmed control unit - Master key in

: a

0.7-sec flash is displayed followed by the LED re-

maining off for 2 sec and then by short 0.46-sec

flashes, the same number of times as there are

keys stored in the memory including the Master

key. When the diagnosis has been completed, the

LED remains permanently OFF. The engine can

be started.

Programmed control unit - fault detected

: a light code is displayed according to the fault detected,

after which the LED remains on steadily. The engine cannot be started. The codes that can be trans-

mitted are:

•

1-flash code

•

2-flash code

•

3-flash code

Diagnostic code - 1 flash

DIAGNOSIS CODE 1 FLASH

This error is identi-

fied as a serial failure. (damaged or shorted to

ground). With this code proceed with the following

checks:

- Antenna power supply: On pin 1 and 2 there must

be battery voltage with the key turned to «

».

(Pin 1 positive, pin 2 negative). Test the continuity

and the insulations of the serial line. Check the

continuity between pin 3 of the antenna and the

corresponding pin on the control unit pin 14.

Carefully check that the connections are free of

oxidation. A more detailed control can be per-

formed by detecting the voltage relative to the

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

Electrical system

ELE SYS - 95

Summary of Contents for 946 E4 EMEA 2021




























































































































































































































































































Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands

VESPA 946 E4 EMEA 2021, Manual

Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands