VESPA 946 E4 EMEA 2021 Manual Download Page 183

Page: 183 / 283

Oil pressure check

- After removing the flywheel cover as described

in the "Flywheel" chapter, remove the electric con-

nexion of the minimum oil pressure switch and

then remove the switch.

- With the engine idling at 1,750 rpm and the oil

temperature at ~90°C, check that the oil pressure

is between 0.5 - 1.2 atm.

- With the engine idling at 5,000 rpm and the oil

temperature at ~90°C, check that the oil pressure

is between 3.2 - 4.2 atm.

- Remove the appropriate tools once the meas-

urement is complete, refit the oil pressure switch

and washer, tightening it to the specified torque

and fit the flywheel cover.

- If the oil pressure is not within the specified limits,

in the following order, check: the oil filter, the oil

by-pass valve, the oil pump and the crankshaft

seals.

N.B.

THE CHECK MUST BE CARRIED OUT WITH OIL AT THE
CORRECT LEVEL AND WITH AN OIL FILTER IN PROPER
CONDITION.

Characteristic

Oil pressure

Operating pressure

- At 1,750 rpm: (0.5 - 1.2)bar

- At 5,000 rpm: (3.2 - 4.2)bar

Locking torques (N*m)

Minimum oil pressure sensor

12 - 14

Crankshaft oil seals

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

Engine

ENG - 183

Summary of Contents for 946 E4 EMEA 2021




























































































































































































































































































Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands

VESPA 946 E4 EMEA 2021, Manual

Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands