VESPA 946 E4 EMEA 2021 Manual Download

Page: 200 / 283

Refitting the injector

- The injector on this vehicle is a twin head injector

with angle different to 90°, an incorrect positioning

of the injector in the throttle body can cause seri-

ous malfunction; it must be observed that the pin

of the spring is placed inside the recess in the in-

jector body as shown in figure.

Removing the butterfly valve

Preventively remove:

- Left side fairing

- Right side fairing

- Air filter

- Rear suspension strut.

Slightly lift the rear part of the vehicle

CAUTION

Injection

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

INJEC - 200

Summary of Contents for 946 E4 EMEA 2021




























































































































































































































































































Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands

VESPA 946 E4 EMEA 2021, Manual

Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands