VESPA 946 E4 EMEA 2021 Manual Download

Page: 55 / 283

Locking torques (N*m)

Hub oil drain screw

15 to 17

Insert through the level check hole the prescribed amount of oil.

Recommended products

Transmission oil 80W-90

Lubricant for gearboxes and transmissions.

SAE 80W-90 API GL-4

Characteristic

Hub oil quantity

300 cm³

Air filter

- Remove the left side fairing.

- Undo the screws indicated.

Unscrew the screw indicated in the figure and re-

move the filter cover complete with air duct.

- Remove the filter element and clean it with water

and shampoo, then dry it off with a clean cloth and

small compressed air jets and immerse it in rec-

ommended oil. Squeeze it between your hands

without twisting it, let it stand until it stops dripping,

and then reinstall it.

CAUTION

IF THE VEHICLE IS USED ON DUSTY ROADS, IT IS NEC-
ESSARY TO SERVICE THE AIR FILTER AND THE CVT

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

Maintenance

MAIN - 55

Summary of Contents for 946 E4 EMEA 2021




























































































































































































































































































Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands

VESPA 946 E4 EMEA 2021, Manual

Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands