VESPA 946 E4 EMEA 2021 Manual Download Page 14

Page: 14 / 283

• Press the ASR on/off button «

» and one of the two brake levers simultaneously for at least 4 seconds.

The activation process will be confirmed by the ASR icon «

» turning on with slow flashing.

• Accelerate to a constant speed of 30 to 40 km/h and maintain it for at least 7 to 8 seconds.

• The end of the procedure will be indicated by the flashing ASR icon «

».

• Once the procedure is complete it is necessary to turn off the vehicle panel (key off) and wait 30

seconds before turning the panel on (key on).

• In case of failure to complete the procedure within 2 minutes the ASR icon «

» will stay on steady and

the ASR will remain off until the panel is turned off (key off).

• To restart the ASR it is necessary to turn on vehicle panel (key on).

It is however necessary to repeat the process until it succeeds.

Static test

Static control after the test drive:

- Restarting when warmed up

- Minimum holding (turning the handlebar)

- Uniform turning of the steering

- Possible leaks

CAUTION

CHECK AND ADJUST TYRE PRESSURE WITH TYRES AT AMBIENT TEMPERATURE.

CAUTION

NEVER EXCEED THE RECOMMENDED INFLATION PRESSURES SINCE THE TYRES MAY
BURST.

Functional inspection

Functional Checks:

Braking system (hydraulic)

- Lever travel

Braking system (mechanical)

- Lever travel

Clutch

- Proper functioning check

Engine

- Proper general functioning and no abnormal noise check

Others

- Check documentation

- Check the frame and engine numbers

- Tool kit

- Licence plate fitting

- Locks checking

Pre-delivery

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

PRE DE - 14

Summary of Contents for 946 E4 EMEA 2021




























































































































































































































































































Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands

VESPA 946 E4 EMEA 2021, Manual

Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands