VESPA 946 E4 EMEA 2021 Manual Download

Page: 149 / 283

Inspecting the hub shaft

- Check the three shafts and the intermediate gear

for wear or distortion of the toothed surfaces, the

bearing housings, and the oil seal housings.

- In case of faults, replace the damaged parts.

Characteristic

Driven pulley shaft

A: 22(-0.01 -0.02)mm

Wheel axle

B: 15(-0.010 -0.020)mm

C: 25(-0.007 -0.020)mm

Intermediate gear

D: 15(-0.01 -0.02)mm

E: 15(-0.01 -0.02)mm

Inspecting the hub cover

- Check that the fitting surface is not dented or distorted.

- Check the bearing bearings.

- In case of faults, replace the damaged components.

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

Engine

ENG - 149

Summary of Contents for 946 E4 EMEA 2021




























































































































































































































































































Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands

VESPA 946 E4 EMEA 2021, Manual

Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands