VESPA 946 E4 EMEA 2021 Manual Download Page 136

Page: 136 / 283

Removing the driven pulley shaft bearing

- Remove the Seeger ring.

CAUTION

PLACE THE COVER ON A SURFACE, REMOVING OR EX-
CLUDING THE ALIGNMENT DOWELS.

- Support the transmission cover adequately.

- Using appropriate tools, remove the bearing.

Specific tooling

020376Y

Adaptor handle

020357Y

32 x 35-mm Adaptor

020412Y

15-mm guide

Refitting the driven pulley shaft bearing

- Use the heat gun to heat the inner part of the lid.

- Using the equipment plant a new bearing, apply

grease on the adapter and guide in order to main-

tain the position of the bearing during operation on

the vertical axis.

Specific tooling

020151Y

Air heater

020376Y

Adaptor handle

020358Y

37 x 40 mm Adaptor

020412Y

15-mm guide

Engine

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

ENG - 136

Summary of Contents for 946 E4 EMEA 2021




























































































































































































































































































Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands

VESPA 946 E4 EMEA 2021, Manual

Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands