VESPA 946 E4 EMEA 2021 Manual Download

Page: 171 / 283

- By means of the table, see the Specifications chapter identify the cylinder base gasket thickness to

be used for refitting. Correctly identify the cylinder base gasket thickness to keep the correct compres-

sion ratio.

- Remove the special tool and the cylinder.

See also

Slot packing system

Refitting the piston rings

- Pistons (like cylinders) are supplied in 4 catego-

ries: A, B, C and D, and must be fitted so that the

reference arrow faces the exhaust duct. The letter

is found at the centre of the piston.

- Fit the sealing rings with the word TOP or the

identification letter facing upwards. In any case,

the step must be facing opposite the piston crown.

- Sealing rings are manufactured with a cylinder

contact conical cross-section and piston gaps

must be offset by 120° in order to obtain a better

bedding.

- Lubricate rings with engine oil when fitting them.

CAUTION

AT EVERY NEW MOUNTING USE RETAINER RING PINS.

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

Engine

ENG - 171

Summary of Contents for 946 E4 EMEA 2021




























































































































































































































































































Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands

VESPA 946 E4 EMEA 2021, Manual

Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands