VESPA 946 E4 EMEA 2021 Manual Download Page 226

Page: 226 / 283

For both bearings of the swinging arm on the frame

side proceed as follows:

- Use handle, adaptor and guide to drive the bear-

ing into its seat.

Specific tooling

020412Y

15-mm guide

020456Y

Ø 24 mm adaptor

020376Y

Adaptor handle

- Insert the axis into the swinging arm on the engine side and then insert the thickness.

- Insert the axis into the swinging arm on the frame side and then insert the thickness.

- Grease in the points indicated by arrows.

Refitting

- Proceed the removal operations but in the reverse order, observing the prescribed tightening torques.

Locking torques (N*m)

Silent block bracket screw

42 to 52

swinging arm to engine - frame pin locknut

76 to 83

Swinging

arm to frame pin locknut

40 - 45

Engine-swinging arm pin

40 - 45

Shock absorbers

Suspensions

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

SUSP - 226

Summary of Contents for 946 E4 EMEA 2021




























































































































































































































































































Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands

VESPA 946 E4 EMEA 2021, Manual

Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands