VESPA 946 E4 EMEA 2021 Manual Download

Page: 215 / 283

- Remove the brakes piping paying attention to the

brake fluid drainage.

- Remove the front and rear brake pumps.

- Undo the screw indicated and remove the rear

handlebar cover.

Refitting

- Proceed with the operations in the reverse order,

observing the tightening torques and paying at-

tention to the correct passage of the cables, the

piping and the cable harness.

THE FIXING SCREW OF THE HANDLEBAR ON THE
STEERING PIPE «1» AND THE NUT «2» MUST BE RE-
PLACED AT EVERY REMOVAL.

Locking torques (N*m)

Handlebar locking screw

40 - 45

Steering column

Removal

- Remove the handlebar

- Remove the front wheel

- Remove the piping of the front brake calliper

- Remove the front speed sensor

- Remove the upper ring nut

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

Suspensions

SUSP - 215

Summary of Contents for 946 E4 EMEA 2021




























































































































































































































































































Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands

VESPA 946 E4 EMEA 2021, Manual

Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands