VESPA 946 E4 EMEA 2021 Manual Download | Manualshive

Page: 281 / 283

background image

CAUTION

MAKE SURE THAT THE CONNECTING CABLE TO THE
NEGATIVE POLE OF THE BATTERY FOLLOWS THE PAS-
SAGE SHOWN IN THE FIGURE IN ORDER TO AVOID POS-
SIBLE FAILURES.

CAUTION

DO NOT REVERSE THE POLARITY: RISK OF SHORT CIR-
CUIT AND DAMAGE TO THE ELECTRICAL SYSTEM.

WARNING

USED BATTERIES ARE HARMFUL FOR THE ENVIRON-
MENT. COLLECTION AND DISPOSAL SHOULD BE CAR-
RIED OUT IN COMPLIANCE WITH REGULATIONS IN
FORCE.

- Place the support band by tightening the previ-

ously removed fixing screws.

- Refit the central cover and lock it by tightening

the relative fixing screws.

N.B.

THE CENTRAL COVER HAS A RUBBER PROTECTION
AGAINST WEATHERING AND OTHER IMPURITIES ON
THE ROAD.
DURING COVER ASSEMBLY, INSERT THE PROTECTION
IN THE COMPARTMENT BETWEEN BODY AND FOOT-
REST, IN FRONT OF THE SWINGING ARM; THEN PRESS
IT AGAINST THE FRONT PART OF THE VEHICLE, IN OR-
DER TO SUPPORT THE BODY, AS SHOWN IN THE FIG-
URE.

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

Chassis

CHAS - 281

«
...
279
280
281
282
283
»

Summary of Contents for 946 E4 EMEA 2021




























































































































































































































































































Reviews:

No comments

Related manuals for 946 E4 EMEA 2021

Brand: Be Cool Pages: 20

Brand: Helge Nyberg Pages: 13

Brand: Wottan motor Pages: 85

Brand: Baja motorsports Pages: 45

Brand: Mod Pages: 2

Street Legal Electric Bike Kit

Brand: Dillenger Pages: 24

Brand: TodaysHighTech Pages: 16

Yes Cart YESMORGMPW4

Brand: Anthro Pages: 4

Brand: PEUGEOT Pages: 52

Brand: Hover-1 Pages: 24

Brand: Razor Pages: 6

Brand: JinCheng Pages: 131

Brand: DENAGO Pages: 77

Brand: WattWheels Pages: 22

Brand: WattWheels Pages: 23

Brand: WattWheels Pages: 26

Brand: 3Style Scooters Pages: 36

Brand: Yamaha Pages: 498

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands