VeEX UX400 User Manual Download Page 16 | Manualshive

Page: 16 / 209

background image

UX400-40G module: 32 Watts

UX400-10G module: 29 Watts

UX400-2.5G module: 20 Watts

UX400-1GE module: 15 Watts

Note: Test Modules become active when one of its test ports is assigned to a Test Application; otherwise they remain inactive
with little or no power consumption.

Total AC/DC Power: 250 Watts

220 Watts available to support any combination of active test modules

Actual power consumption (per module) may vary depending on configuration/settings and optic modules being used. Values

listed are maximum estimated ratings for the most demanding conditions.

Inactive modules (not assigned to a test application) do not consume power.

When working on battery-only mode, the UX400 notifies users when the maximum battery capacity has been reached or it is not

enough to support the new module user is trying to activate.

4.3.2 Battery Overdraw Protection

On battery power, when the capacity reaches 10%, the UX400 notifies users with a pop-up warning message and an

intermittent audible alarm.

If the previous message is ignored and the total capacity falls under 5% the UX400 immediately initiates the emergency

shutdown procedure for safety and to protect its battery from damage. Once in this mode all power to modules is

immediately cut and test files are not saved.

In the event that the load exceeds the 95W battery limit when the AC power is interrupted or AC/DC adapter is

unplugged, the UX400 would immediately initiate the emergency shutdown procedure to protect its battery from damage or

any other safety issues. Once in this mode all power to modules is immediately cut and test files are not saved.

4.4 Connectors and Panels

4.4.1 Test Modules

1G Test Module:

UX400 10G e-Manual D07-00-058P RevA00

Page 16 of 209

«
...
14
15
16
17
18
...
»

Summary of Contents for UX400


















































































































































































































Reviews:

No comments

Related manuals for UX400

Brand: Baccara Pages: 16

Brand: Salda Pages: 20

Brand: TCi Pages: 9

Brand: +GF+ Pages: 3

Brand: Össur Pages: 58

Brand: Mitsubishi Pages: 16

Brand: SOMFY Pages: 4

Brand: Seiko Pages: 30

ASC G Wi-Fi kit

Brand: Waeco Pages: 386

Brand: Nordelettronica Pages: 8

Brand: Valence Tech Pages: 12

Brand: Dungs Pages: 56

Brand: Emec Pages: 8

Brand: Wilo Pages: 128

Brand: Dantherm Pages: 28

Brand: Unimig Pages: 4

Brand: Eaton Pages: 2

RSF B mini Series

Brand: Harmonic Drive Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands