manualshive.com logo in svg

VeEX UX400, User Manual, Page: 117 / 209

Share
Download
VeEX UX400 User Manual Download Page 117

Rx=Tx:

 Rx blocks will copy the settings made in the Tx blocks

Changes to the Setup are applied immediately unless an invalid parameter has been selected.

When the TX and RX signal structures need to be independent or asymmetrical, uncoupling the transmitter and receiver is possible. For example, the TX could be sending a PRBS

of 2^23-1 in a VC12 carried within an optical STM-64, while the RX could be expecting to receive a PRBS of 2^23-1 in a 2Mbps E1 signal.

7.1.1.1 Hierarchy:

 Allows the user to configure the following:

Operating Mode:

Normal:

 Unit working as normal mode.

Payload:

 Overhead overwrite Editing Thru mode allows for some intrusive error and alarm injection through overhead manipulation. Applies to both SDH/SONET and

PDH signals and allows the user to configure low rate signal (if applicable) and associated framing.

Transparent:

 All the traffic goes through the unit untouched and the unit can monitor it. It is comparable to Monitor mode with a 10/90 splitter. In Transparent mode,

the unit regenerates the signal in amplitude. The clock is recovered from the received signal.

Note: 

Through modes are used to test network behavior under certain conditions, such as alarms and APS. To select Payload Through, the payload has to be the same for

the relevant ports.

Network Type:

 SONET/ SDH or OTN

Note:

 The choice between SDH and SONET Network Type is based on the selection made in the menu under General tab.

Test Rate:

 OC-192-10G (for SONET), STM-64 - 10G (for SDH), OTU-2 (for OTN)

OTN Mapping 

(for OTN only)

:

 PRBS, OC192 SYNC, OC192 ASYNC, STM-64 SYNC, STM-64 ASYNC

Note:

 ITU-T G.709 and STS mappings per Bellcore GR-253 and ANSI T1.105 recommendations are supported. ITU-T G.709 and both AU-4 and AU-3 signal

mappings per G.707 recommendations are supported. The multiplexing structures are shown below.

OTN SONET Mapping Structure

OTN SDH Mapping Structure

Scrambler

 (for OTN only)

: 

ON / OFF

FEC

 (for OTN only)

:

 ON / OFF

Heirarchy Menu SDH / SONET

Heirarchy Menu OTN

UX400 10G e-Manual D07-00-058P RevA00

Page 117 of 209

Summary of Contents for UX400


















































































































































































































Reviews:

No comments