manualshive.com logo in svg

VeEX UX400, User Manual

The VeEX UX400 user manual is available for free download from manualshive.com. This comprehensive manual provides step-by-step instructions and detailed information about operating and troubleshooting the UX400, helping users maximize their experience with this advanced product. Get your free manual today and unlock the full potential of the VeEX UX400.

Share
Download
background image

Go back to top

 

Go back to TOC

7.4.4.2 Received Traces (RX)

J0 [Section]: Regenerator section trace/Section Layer trace

Program a 1, 16-byte or 64-byte identifier to set and check the expected trace

Enable or disable the TIM (Trace Identifier Mismatch) alarm

J1 [STS Path]: High order path section trace/STS path section trace.

Program a 16 or 64-byte identifier to set and check the expected trace

Enable or disable the TIM (Trace Identifier Mismatch) alarm

J2 [VT Path]: Low order path section trace

Program a 16 or 64-byte identifier to set and check the expected trace

Enable or disable the TIM (Trace Identifier Mismatch) alarm

Note: 

To program or edit the received trace, tap on the applicable trace box and this will launch the QWERTY keyboard.

RX - JO [S]

Go back to top

 

Go back to TOC

7.4.5 Payload Labels

This function is used to set the C2 and V5 Path Signal Labels that indicate the content of the High order and Low order VCs.

Tap the Payload Label icon to display the payload label screens. There are dedicated tabs for Transmitted and Received payload labels and setups:

C2 [STS Path]: Path signal label

Specifies the mapping type in the STS-1n

Program the TX or RX label by editing the hexadecimal value or by using the convenient drop-down menu selection

For the RX label, you can enable or disable the Payload Mismatch (PLM) Alarm

Payload Label TX

Payload Label RX

UX400 10G e-Manual D07-00-058P RevA00

Page 166 of 209

Summary of Contents for UX400


















































































































































































































Reviews:

No comments

Related manuals for UX400

Laars SC6 Installation And Operation Instructions Manual preview
SC6
Brand: Laars Pages: 28
Oceanic Systems 5980 User Manual preview
5980
Brand: Oceanic Systems Pages: 8
J+J J4C S20 Quick Start Manual preview
J4C S20
Brand: J+J Pages: 4
Val Controls I 24-AF Series Replacement Manual preview
I 24-AF Series
Brand: Val Controls Pages: 6
Procom DGC-6D Operating Instructions Manual preview
DGC-6D
Brand: Procom Pages: 10
Remote Control Systems TITAN-TRACKSIDE-3 Instruction Manual preview
TITAN-TRACKSIDE-3
Brand: Remote Control Systems Pages: 4
ACTi R12CP-30 Installation Manual preview
R12CP-30
Brand: ACTi Pages: 20
SOARNEX EWC-100 Quick Installation Manual preview
EWC-100
Brand: SOARNEX Pages: 14
Tristan Auron DT2420 User Manual preview
DT2420
Brand: Tristan Auron Pages: 30
ICP DAS USA ALM-04-MRTU User Manual preview
ALM-04-MRTU
Brand: ICP DAS USA Pages: 26
National Instruments cRIO-FRC II User Manual And Specifications preview
cRIO-FRC II
Brand: National Instruments Pages: 22
ICS Tunnel Master Jr User Manual preview
Tunnel Master Jr
Brand: ICS Pages: 70
Allen-Bradley CENTERLINE Instruction Manual preview
CENTERLINE
Brand: Allen-Bradley Pages: 88
Grundfos DDI Series Supplement To Installation And Operating Instructions preview
DDI Series
Brand: Grundfos Pages: 12
Weidmüller 1517130000 Manual preview
1517130000
Brand: Weidmüller Pages: 18
Viper 7752v Owner'S Manual preview
7752v
Brand: Viper Pages: 2
Daikin BRC301B61 Operation Manual preview
BRC301B61
Brand: Daikin Pages: 10
Neousys Technology Nuvo-3000 Series User Manual preview
Nuvo-3000 Series
Brand: Neousys Technology Pages: 101

Brands by name

Popular brands

Load more brands