manualshive.com logo in svg

VeEX UX400, User Manual

Share
Download
VeEX UX400 User Manual Download Page 41

 

Go back to top

 

Go back to TOC

6.2.1.1 Header Settings

BERT Profile:

 Load a previously configured test profile or create a new profile from existing settings. Currently its set to "Default".

Test Layer:

 Select the test layer to perform the BERT

Options are Layer 2, Layer 3 and Layer 4

Frame Type:

Layer 2: 802.3 Raw (IEEE 802.3 frame without LLC) and Ethernet II (DIX) (named after DEC, Intel, and Xerox, this is the most common frame type today)

Layer 3: Ethernet II (DIX)

No Frame Type for Layer 4

MAC/IP:

 Tap the MAC and IP blocks on the Frame image to access the setup menus

Set the Source and Destination MAC address for Layer 2

Set the Source and Destination MAC and IP addresses for Layer 3 and 4

VLAN: 

Off, 1 tag, 2 tags, 3 tags

The user is able to configure up to 3 VLAN tags (VLAN stacking, for Q-in-Q applications)

Note: 

VLAN stacking is an option

MPLS:

 (For Layer 3 and 4 only) Off, 1 tag, 2 tags, 3 tags

The user is able to configure up to 3 MPLS tags

Note: 

MPLS tag configuration is only available when the MPLS option is purchased

PROTOCOL (Layer 4 only)

: UDP or TCP

The most common Ethernet Frame format, Type II

Go back to top

 

Go back to TOC

MAC, VLAN, MPLS, IP, and Test Pattern Configurations:

To configure the MAC addresses, IP addresses, VLAN tag(s), MPLS tag(s), and test pattern, tap on the frame image displayed on the screen. This brings up the

configuration screens for all the header fields.

MAC Header Tab:

MAC Source: 

Use the default source address of the test set or configure a new or different address.

MAC Destination

: Configure the destination MAC address of the far-end partner test set or use the ARP or ARP GW keys to determine the MAC address of

the destination IP address (ARP) or the Gateway (ARP GW). Note that a valid IP connection needs to be up to use these functions. Refer to 

9.1 IP

 in the

V300 Common Functions manual

 for details on IP connection.

Ethernet Type: 

For Layer 3 & 4 testing, the Ethertype is set to 0800-IP. For Layer 2, it can be typed in.

BERT Setup MAC Layer 2

BERT Setup MAC Layer 3 & 4

UX400 10G e-Manual D07-00-058P RevA00

Page 41 of 209

Summary of Contents for UX400


















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands